「7臺セット」Aruba APIN0303 AP-303-JP 無線LAN アクセスポイント動作確認済み、初期化済み

* Aruba APIN0303

* S/N : CNHNK9T07J

* Factory reset

* Login ID : admin

* Password : CNHNK9T07J

APBoot 2.4.1.10 (build 65756)

Built: 2018-07-11 at 21:04:12

Model: AP-303

DRAM: 512 MiB

Flash: Detected MX25R3235F: with write protection total 4 MiB

NAND: 128 MiB

Power: POE

Net: eth0

Radio: ipq4019#0, ipq4019#1

FIPS: passed

Hit <Enter> to stop autoboot: 0

apboot>

apboot> purgeenv

preserving os_partition (0)

Erasing SPI flash...Writing to SPI flash...done

apboot>

apboot> factory_reset

Clearing state...

Checking OS image and flags

Image is signed; verifying checksum... passed

Preserving image partition 0

Erasing flash sector @ 0x3a0000... OK

Erasing UBIFS ...done

Purging environment...

preserving os_partition (0)

Erasing SPI flash...Writing to SPI flash...done

apboot>

apboot> boot

Booting OS partition 0

Checking image @ 0x0

Copying image from 0x84000000

Image is signed; verifying checksum... passed

SHA2 Signature available

Signer Cert OK

Policy Cert OK

RSA signature verified using SHA2.

Uncompressing Kernel Image ... OK

[ 0.000000]

[ 0.000000] Aruba Networks

[ 0.000000] ArubaOS Version 8.10.0.7-8.10.0.7 (build 87023 / label #87023)

[ 0.000000] Built by jenkins@f3181d84704d on 2023-06-06 at 17:25:03 UTC (gcc version 4.6.3)

[ 0.000000]

[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d

[ 0.016508] SMP: Total of 4 processors activated (384.00 BogoMIPS).

[ 0.051186] i2c-gpio driver registered

[ 16.828853] 3 ofpart partitions found on MTD device 7980000.qcom,nand

[ 16.895894] Creating 3 MTD partitions on "7980000.qcom,nand":

[ 16.964632] 0x000000000000-0x000002000000 : "aos0"

[ 17.063688] 0x000002000000-0x000004000000 : "aos1"

[ 17.150239] 0x000004000000-0x000008000000 : "ubifs"

[ 17.285706] m25p80 spi0.0: found mx25r3235f, expected n25q128a11

[ 17.385106] Found AT97SC3203 on MSM-I2C-v2-adapter

[ 17.440746] Key type dns_resolver registered

[ 17.481056] Registering SWP/SWPB emulation handler

[ 18.608350] Watchdog run with TZ supported gpio reset

[ 18.692293]

Starting Kernel SHA1 KAT ...

[ 18.726758] Completed Kernel SHA1 KAT

[ 18.773795] Starting Kernel HMAC-SHA1 KAT ...

[ 18.823849] Starting Kernel DES KAT ...[ 18.869540] Completed Kernel DES KAT

[ 18.913312] Starting Kernel AES KAT ...

[ 18.957033] Completed Kernel AES KAT

[ 18.957033]

[ 19.020621] Starting Kernel AESGCM KAT ...

[ 19.067361] Completed Kernel AESGCM KAT

[ 19.116614] Completed Kernel HMAC-SHA1 KAT

Thu Jan 1 00:00:00 PST 1970

Populate AP type info

Domain Name: SetMeUp.arubanetworks.com

Current OEM Name : Aruba Networks

Disabling ipv6 for devices by default

AP-type has_ble_support: ONBOARD.

IPv6 capability is supported for devices

No panic info available

Enabling ble_daemon and ble_relay via nanny

glenmorangie: Start hotplug

apfcutil: sector CACHE: Cache uninitialized

apfcutil: sector RAP: Cache uninitialized

apfcutil: sector FAT: Cache uninitialized

apfcutil: sector DRT: Cache uninitialized

apfcutil: sector SCRATCH: Cache uninitialized

Backup ENV.

apfcutil: sector MESH Prov: Cache uninitialized

Installing glenmorangie ethernet driver

[ 31.752923] edma module_init

Enter non-FIPS mode

Cfg len is 0

Configuration file is empty, turning on default services...

extended ssid activate due to no AP config ...

The AP is in factory default status

Mesh enabled

single uplink platform

Starting watchdog process...

Aruba watchdog daemon started [4 thread(s)]

touching file /tmp/ip_mode_0

Enable IPv6 for the Conductor v6 discovery

Enabling DHCPv6 ...

Checking country code.

Ethernet uplink bond0 not active yet

error in reading source file

No uplink active. Becoming Mesh Point

Factory default ap without uplink, it will become a point.

Str Mesh Split5G Band Range:

Mesh Split5G Band Range: 0

copying bootuplog ...

[ 68.969254] uol: module license 'Proprietary' taints kernel.

[ 69.024551] Disabling lock debugging due to kernel taint

[ 69.089571] uol_init_driver:435 HW offload not applicable, AP will use cutting through path!

allow PAPI

set device anul0 mtu to 2000

notify asap_mod 3g no present...

Enabling IPv6 for devices... IP mode is v4-only...

/etc/init.d/rcS: 3178: cannot create /proc/sys/net/ipv6/conf/br0/accept_ra_rt_info_max_plen: Directory nonexistent

/etc/init.d/rcS: 3178: cannot create /proc/sys/net/ipv6/conf/default/accept_ra_rt_info_max_plen: Directory nonexistent

apdot1x authentication is not enabled

skip dhcp when loop or wifi-uplink without eth detected !!!!!!!!!!!!!

waiting for default ip ready ...

[ 159.442052] Picked up default IP a9fe343f, rand 343f

[ 165.454045] Default IP is ready

Installing default ip.

Default IP comes up.

[ 166.456112] ip_time_handler: Got ip and packets on bond0 Started conductor election 1-0, rand 27

Compressing all files in the /etc/httpd directory...

Done.

Starting Webserver

bind: Transport endpoint is not connected

Put ntpdate to the nannylist.

AP rebooted caused by cold HW reset(power loss)

shutting down watchdog process (nanny will restart it)...

<<<<< Welcome to the Access Point >>>>>

Completed SW FIPS KAT test

Power supply mode is POE:, USB Modem is not present.

User: [ 180.390084] Starting Kernel HMAC SHA1 FIPS KAT ...

[ 180.432876] Completed Kernel HMAC SHA1 FIPS KAT

[ 182.392056] Starting Kernel HMAC SHA256 FIPS KAT ...

[ 182.436929] Completed Kernel HMAC SHA256 FIPS KAT

ble_ready NOT present @init ....

[ 184.400056] Starting Kernel HMAC SHA384 FIPS KAT ...

[ 184.444930] Completed Kernel HMAC SHA384 FIPS KAT

[ 186.400066] Starting Kernel HMAC SHA512 FIPS KAT ...

[ 186.444930] Completed Kernel HMAC SHA512 FIPS KAT

User: admin

Password:

Warning: CLI module is running in a degraded state. Configuration, write memory, and support command are disabled; please debug with caution.

show tech-support and show tech-support supplemental are the two most useful outputs to collect for any kind of troubleshooting session.

7c:57:3c:cc:a5:ea#

7c:57:3c:cc:a5:ea# sh ver

Aruba Operating System Software.

ArubaOS (MODEL: 303), Version 8.10.0.7 LSR

Website: http://www.arubanetworks.com

Compiled on 2023-06-06 at 17:25:03 UTC (build 87023) by jenkins

FIPS Mode :disabled

AP uptime is 6 minutes 15 seconds

Reboot Time and Cause: AP rebooted caused by cold HW reset(power loss)

7c:57:3c:cc:a5:ea#

7c:57:3c:cc:a5:ea# sh run

version 8.10.0.0-8.10.0

virtual-controller-key 2183503a015ea43ce6582d831495bda45289bfd0ef0ace9e59

name SetMeUp-CC:A5:EA

clock timezone none 00 00

rf-band all

arm

wide-bands 5ghz

min-tx-power 18

max-tx-power 127

band-steering-mode prefer-higher-band

air-time-fairness-mode default-access

syslog-level warn ap-debug

syslog-level warn network

syslog-level warn security

syslog-level warn system

syslog-level warn user

syslog-level warn user-debug

syslog-level warn wireless

auth-survivability cache-time-out 24

wlan external-captive-portal

server localhost

port 80

url "/"

auth-text "Authenticated"

blacklist-time 3600

auth-failure-blacklist-time 3600

ids

wireless-containment none

uplink

preemption

enforce none

failover-internet-pkt-lost-cnt 10

failover-internet-pkt-send-freq 30

failover-vpn-timeout 180

airgroup

disable

airgroupservice airplay

disable

airgroupservice airprint

disable

7c:57:3c:cc:a5:ea#

7c:57:3c:cc:a5:ea# sh sum su

Name :SetMeUp-CC:A5:EA

System Location :

Domain :

VC IP Address :0.0.0.0

VC IPv6 Address :::

AP1X :NONE

VC VLAN :0

VC Mask :0.0.0.0

VC Gateway :0.0.0.0

VC DNS :0.0.0.0

IP Mode :v4-only

Cluster-Security DTLS:disable

Content Filtering :disable

Terminal Access :disable

Telnet Server :disable

Activate Disable :disable

Organization :

Disable ciphers :

Airwave Server :

Airwave Backup Server:

Airwave Prov Backup :

Number of VC transition :0

Airwave Shared Key :

Airwave Config Via :DHCP

Airwave :Not Set Up

Aruba Central Server :

Aruba Central :Not Set Up

Managed Via :Local

Syslog Server :0.0.0.0

Syslog Level :warn

Band :all

Conductor IP Address :0.0.0.0

IP Address :169.254.52.63

Netmask :N/A

Gateway :N/A

IPv6 Address :--

Conductor Key :2183503a015ea43ce6582d831495bda45289bfd0ef0ace9e59

Elected Time :6m:27s

Dynamic Radius Proxy :disable

Dynamic Tacacs Proxy :disable

NTP Server :

Configuration Dirty :disable

Allow New APs :disable

Classification :disable

Containment Confirm :disable

Wireless Containment :disable

Wired Containment :disable

Wired Containment AP Adjacent MAC :disable

Wired Containment Suspect L3 Rogue :disable

Rogue Containment :disable

LED Off :disable

AppRF Visibility :none

URL Visibility :disable

WebCC Visibility :disable

Image Server State :success

Image Server Message :Success

New Image Version :

New Image URL :

Factory SSID :SetMeUp

Image Sync Via :Conductor

AP Alerts :0

Client Alerts :0

Active Faults :0

Fault History :0

Usb Support :NO

Serial Number :CNHNK9T07J

OpenDNS Status :Not connected

TFTP Dump Server :0.0.0.0

Extended SSID :disable

Mesh role detect :disable

Inactivity-ap-timeout:60

Config Sync Status :TRUE

VPN Status :Not Set Up

Mobility Acccess Switch Integration :disable

Deny inter user bridging :disable

Deny local routing :disable

Support Connection Status :Not Connected

Dynamic CPU Management:auto

Restrict Corporate Access:disable

SLAAC IP Address:--

Link Local IP Address:--

0 Clients

---------

MAC Name IP Address ESSID Access Point

--- ---- ---------- ----- ------------

0 Networks

----------

Profile Name ESSID Clients Status Type

------------ ----- ------- ------ ----

0 Access Points

---------------

MAC IP Address Name Clients Need Antenna Config

--- ---------- ---- ------- -------------------

Restricted Management Access Subnets

------------------------------------

Subnet IP Address Subnet Mask

----------------- -----------

RADIUS Servers

--------------

Name IP Address Port Key Timeout Retry Count NAS IP Address NAS Identifier RFC3576 Airgroup RFC3576-ONLY Airgroup RFC3576 port DRP IP DRP Mask DRP VLAN DRP Gateway RFC5997

---- ---------- ---- --- ------- ----------- -------------- -------------- ------- --------------------- --------------------- ------ -------- -------- ----------- -------

InternalServer 127.0.0.1 1616 ba14080f920af2028caa1ea7da10abbffd1602ad3f80b4ed41132a80f04fb436993d4a172efa4c4b7b66c0adc17b5d66094247c7e3a7d17ef2221f89cc5d6e34 5 3 0 n

RTLS Servers

------------

Type Address Port Key Frequency Include Unassociated Stations CM

---- ------- ---- --- --------- ----------------------------- --

Aeroscout 0 disable N/A

Airwave 0 0 disable enable

1 AP Class

----------

Name APs

---- ---

Ursa 0

OOS Hold On Time :30

Manual Denylist Count :0

Dyn Denylist Count :0

Certificate Installed: :No

Internal Radius Users :0

Internal Guest Users :0

Internal User Open Slots :512

Openflow Server :

Openflow Server Port:30633

Openflow Server tls-enable:False

PAN Firewall Port :443

PAN Firewall Status :Disabled

Auto save :Enabled

Stats Sample Cnt :15

Stats Interval :30

Monitor Interval :0

Need central wizard :No

Info timestamp :387

Uplink switch native VLAN:0

Radius RFC3576 Listen Port :3799

New Password :Do not change password

split 5ghz mode :disable

Application monitoring :disable

Airslice policy :disable

■ 保証期間： NC/NRでお願いします。

■ 発送方法: 佐川/ヤマト運輸(運送會社のご指定はできません。)

■送料について：梱包資材の費用や配送業者に持ち込む際に発生する交通費などが含まれていますので、ご了承下さい。

[重要]多數商品を落札する場合は、システム上のまとめ取引申請を行って下さい。

お支払い後の取引メッセージでの同梱申請は固くお斷り致します。

支払い過剰の送料は返金出來かねます。必ずご確認の上で料金をお支払い下。

落札者側の地域間違いの場合も同様ですので、ご注意願います。

■ 入札前にご確認ください

* 上記以外のチェックは行なっておりません。その他詳細はすべて未確認です。

* 電話応対は不可です。取引ナビ及び質問欄でご連絡ください。

* 多忙な為、リアルタイムの返答はできかねますので余裕をもっての投稿?質問をお願い致します

* 質問落札後の対応は営業時間(平日９：００～１７：００)內になります。

* 落札物到著後のサポート?使用方法の問合せにはお答えする事は出來ません

* 當方も別業者さんから譲られたものなので詳しい事情、パスワード及び分解痕跡などの確認することはできません。

* 連絡事項がある場合、受領後48時間以內に取引ナビでご連絡お願いします。

* 現狀の狀態を分かりやすく表記するようにしておりますが、程度の基準相違や表記しきれない部分もあります。神経質な方は入札をご遠慮ください。

* 中古品につきましては、可能な限り清掃し出品しておりますが、ヨゴレ等が多少殘っている場合もあります。予めご了承ください。

* 中古品につきましては、畫像は特別な記載がない限り「現品」です。畫像にて狀態をご確認ください。

* ジャンク、現狀品、保証なし商品については、いかなる場合（萬一のスペック記載違い含む）においても保証?返品?クレーム対象外でお願いします。

* ジャンク扱い商品については、記載の瑕疵が悪化する、または記載の瑕疵に起因し記載以外の瑕疵が発生する可能性もあります。

* 落札して頂いた後全く連絡か取れない方か多く、イタズラ入札が多発しております。申し訳ありませんが、新規さまの方のご入札はご遠慮いただいております。ご入札頂きましても削除させていただく場合がありますので、ご了承下さい。

上記の為、記載の現在の狀態や畫像の狀態を保証するものでもありません。十分にご理解の上での入札をお願いします。